SSV Works MT-2A Can-Am Maverick Trail-Sport Complete 2-Speaker Kit
We are a SSV Works authorized dealer so you get up-to-date, fully warrantied products. Shipping is free to the lower 48 states on everything you order!
What's Inside?
- • (2) Speaker Kit
- • Owner's Manual
Complete Powersports Audio, Built to Fit
Upgrade your Side-by-Side with a complete SSV Works audio system featuring a direct-fit MRB3 Bluetooth receiver, front kick-panel speaker pods, amplifier mounting system, and plug-and-play wiring. The WP-A6 speakers deliver 120W peak power with crisp titanium-tweeter highs and rugged weather protection for sound that stays clear through mud, heat, rain, and rough trails.
Bolt In. Plug In. Ride With Bigger Sound.
Get a cleaner factory-style audio upgrade without cutting your vehicle. This complete system combines a direct-fit dash kit, durable 6.5-inch SSV Works speakers, dedicated amp mounting, and ready-to-connect harnesses. UV-stable construction, EPDM sealing, and positive-lock connectors keep the system protected while you enjoy powerful trail-ready audio.
Frequently Asked Questions (FAQ)
- • Why does the MT-2A sound different after changing the speaker location?
Moving the speakers changes their distance and direction relative to the occupants. In an open UTV, even a small change in positioning can affect how clearly vocals and higher frequencies are heard.
- • What causes a hollow or distant sound from the speakers?
A hollow sound can occur when the speakers are wired out of phase or when their placement creates unusual acoustic reflections. Verify positive and negative connections before changing the amplifier settings.
- • Why does the speaker sound normal until the vehicle reaches higher speeds?
Wind and engine noise can mask parts of the audio spectrum once the vehicle is moving quickly. If the system is already close to its maximum clean output, this background noise can make the speakers seem significantly weaker.
- • What should I check if the speaker makes a buzzing noise after installation?
Inspect the speaker mounting surface, hardware, grille, and nearby trim for unwanted vibration. If the buzz changes with engine speed, also investigate the audio system's grounding and signal wiring.
- • Can the MT-2A be installed where it receives direct sunlight?
The installation location should provide reasonable protection from excessive heat and environmental exposure. Avoid mounting the component where prolonged direct heat could raise operating temperatures unnecessarily.
- • Why does the audio cut out when the UTV hits a large bump?
A loose connector or poorly supported cable can momentarily disconnect when the vehicle experiences a hard impact. Secure the wiring and inspect every connection for movement or damaged terminals.
- • What happens if the speaker enclosure is not sealed properly?
An improperly sealed enclosure can reduce acoustic performance and allow unwanted vibration or air leakage. Check the mounting surface and enclosure for gaps before trying to compensate with EQ adjustments.
- • Why does the MT-2A sound too bright after adding an amplifier?
A new amplifier can change the system's overall gain and tonal balance. Reduce excessive treble or adjust the amplifier gain rather than immediately assuming the speakers are defective.
- • How can I prevent the speaker hardware from loosening?
Use the correct mounting hardware and make sure the speaker is seated evenly against its mounting surface. Periodically inspect the fasteners, especially if the vehicle is frequently driven over rough terrain.
- • Why does the system sound unbalanced after adding another pair of speakers?
Additional speakers can change the overall impedance and alter how the amplifier distributes power. Recheck channel assignments, balance, gain, and crossover settings so the new speakers integrate properly with the existing system.
Features:
- Matches factory color and texture
- Fits the SSV Works MRB3 unit
- No cutting required
- The 25mm Ti- tweeter creates crisp brilliant highs engineered to be heard outdoors, even in a helmet…over the motor…haulin’ down the trails. The grille mounted tweeter allows for peak cone clearance and maximum output while providing a low profile with optimal weatherproofing.
- SSV Works speakers feature a unique positive lock connector to prevent speaker wire detachment inside the enclosure. No matter how hard you drive, your speakers will keep on rockin’.
- Marine speakers are great for boats; however boat speakers don’t get as wet, dirty or muddy as you do in a Side X Side. WP-A6 speakers feature an EPDM duo lock gasket surrounding the speaker to keep the water out and the sound pressure in. EPDM conforms to the surface and seals tight no matter where you ride, in direct UV, extreme heat, or in freezing temps.
- Specs: 6.75” Powersports marine speaker with 25mm Titanium hard dome tweeter, Santoprene surround, UV Stable ASA plastic grille with optional Chroma grille color inserts, 2-pin posi-lock connectors, 4ohm, 60w RMS/120w peak power, just 2-3/16” (5.5 cm)
Complete the system includes:
- Direct-Fit dash kit with MRB3 Bluetooth Receiver
- Front kick panel speaker pods with SSV Works 6.5" speakers
- Direct-Fit amp mounting systemr
- Plug-&-Play harness, wiring and cables.
- UPC: 815172014089
- Weight: 15
- Authorized Internet Dealer
Warranty: 2 Year(s) Warranty.
This item is accompanied by a manufacturer's warranty. If it is found to be defective, it may be returned to OnlineCarstereo.com for replacement within 2 Year(s) from the original date of purchase with proper return authorization.
