Wet Sounds HTX-2 Hydro-Tech X (HTX) Series 2-Channel 300W RMS x 2 at 2 Ohms, Full Range Class-D, High Performance Marine Audio Amplifier
We are a Wet Sounds authorized dealer so you get up-to-date, fully warrantied products. Shipping is free to the lower 48 states on everything you order!
What's Inside?
- • Hydro-Tech X (HTX) Series 2-Channel Full Range Class-D, High Performance Marine Audio Amplifier
- • (2) 30A ATO fuses (installed)
- • 2.5mm Allen wrench
- • Owner's Manual
Why Choose Wet Sounds HTX-2 Marine Amplifier?
Hydro-Tech™ X (HTX) Series Amplifier
It represents the ultimate in High Performance Marine Audio. Wet Sounds HTX Series Marine Amplifiers are designed to be a complete solution for every type of extreme marine application. HTX amplifiers use superior performance circuitry by utilizing Class D Power Supplies. These amplifiers have extreme power output packed inside a small chassis, thermal overload protection, flexible crossovers, and extended inputs. HTX amplifiers are a well-balanced match for all of the Wet Sounds™ products.
Designed by Boaters for Boaters
Designed by boaters for boaters, Wet Sounds made this Hydro-Tech™ X amplifier to survive and thrive in the often-harsh marine environment. A conformal-coated circuit board, a sealed, saltwater-resistant heat sink, and stainless steel hardware ensure that your amp will stand up to salt, spray, high temperatures, and high volume levels for seasons to come.
Frequently Asked Questions (FAQ)
- • What should I check if the amplifier will not turn on?
Check the battery voltage, fuse, ground connection, and remote turn-on wire. Make sure all power terminals are secure and free from corrosion.
- • How should I set the gain controls?
Start with the gain at a low setting and gradually increase it. Stop before distortion occurs to prevent clipping and protect connected speakers.
- • Can I bridge the two channels for more power?
Yes, if your speaker or subwoofer impedance meets the amplifier's bridging requirements. Follow the recommended wiring configuration before connecting a bridged load.
- • What causes the amplifier to enter protection mode?
Overheating, low impedance, shorted wiring, or excessive voltage can activate protection mode. Check speaker connections and allow the amplifier to cool before restarting.
- • How can I reduce engine noise through my speakers?
Check the ground connection and route RCA cables away from power wiring. Loose grounds or electrical interference can introduce unwanted engine noise.
- • What crossover setting should I use for speakers?
Use the high-pass filter for full-range speakers to reduce excessive bass. Adjust the crossover frequency based on speaker size and your system's configuration.
- • Why does the amplifier become hot during use?
Some heat is normal during operation. Ensure proper ventilation and check the speaker impedance, wiring, and gain settings to prevent excessive overheating.
- • Can this amplifier be installed in a marine environment?
Yes. It is designed for marine applications. Mount it in a secure location and protect wiring connections from excessive moisture and corrosion.
- • What should I inspect if there is no sound?
Check the source unit, RCA cables, speaker wiring, gain settings, and amplifier power. Confirm the input signal and connected speakers are functioning correctly.
- • Why does the sound cut out at high volume?
Check for overheating, voltage drop, low speaker impedance, or clipping. Insufficient electrical power can also cause the amplifier to shut down temporarily.
- Maximum Power : 600 Watts
- Low Frequency Response : 50-250 Hz
- Number of Channels : 2
- Frequency Response : 20-20000 Hz
- Built In Crossovers : Yes
- RMS Power Output : 300x2 Watts
- Channel Separation : Yes
- Color : Silver
- Amplifier Class : D
Features:
- 2-channel marine amplifier
- Class-D design
- 150 watts RMS x 2 at 4 ohms (300 watts RMS x 2 at 2 ohms)
- 600 watts RMS x 1 at 4 ohms
- high- and low-pass filters
- rugged, water-resistant shell
- removable speaker terminal blocks for easier installation
- 4-gauge power and ground leads recommended — wiring and hardware not included with amplifier
- fuse rating: 30A x 2
- frequency response: 20-20,000 Hz
- dimensions: 9-9/16"W x 3-1/8"H x 7-3/16"D
Specifications:
- RMS Power Output (Watts x Channels) 150 x 2
- Frequency Response at Rated RMS Power 100Hz Hz
- THD at Rated RMS Power 1%
- Signal to Noise Ratio 90 dB
- Input Voltage 14.4v
- Peak Power Output (Watts x Channels) N/A
- Power at 2 Ohms (Watts x Channels) 300 x 2
- Bridged Power (Watts x Channels) 600 x 1
- Minimum Impedance Bridged 4
- Minimum Impedance Unbridged 2
- UPC: 814820022179
- Weight: 6
- Authorized Internet Dealer
Warranty: 2 Year(s) Warranty.
This item is accompanied by a manufacturer's warranty. If it is found to be defective, it may be returned to OnlineCarstereo.com for replacement within 2 Year(s) from the original date of purchase with proper return authorization.
